# DEVICE:URL:REPORT: https://lists.alioth.debian.org/pipermail/nut-upsdev/2015-July/007025.html # DEVICE:URL:VENDOR: http://fideltronikinigo.com/viper/viper-1200/ # DEVICE:COMMENT: # Vendor site: http://fideltronikinigo.com/viper/viper-1200/ # # The blazer_usb driver did not work with this device. # # `test.battery.*` commands were presented by driver, but do not work. # # Source and additional logs: http://lists.alioth.debian.org/pipermail/nut-upsdev/2015-July/007025.html # DEVICE:EOC battery.charge: 100 battery.runtime: 600 battery.voltage: 27.70 battery.voltage.high: 26.00 battery.voltage.low: 20.80 battery.voltage.nominal: 24.0 device.model: 1200VA device.type: ups driver.name: nutdrv_qx driver.parameter.bus: 004 driver.parameter.chargetime: 28800 driver.parameter.idleload: 10 driver.parameter.offdelay: 60 driver.parameter.ondelay: 60 driver.parameter.pollfreq: 30 driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.parameter.product: MEC0003 driver.parameter.productid: 0000 driver.parameter.runtimecal: 60,100,900,21 driver.parameter.synchronous: no driver.parameter.vendor: MEC driver.parameter.vendorid: 0001 driver.version: 2.7.3.1 driver.version.data: Megatec 0.06 driver.version.internal: 0.21 input.current.nominal: 5.2 input.frequency: 50.0 input.frequency.nominal: 50 input.voltage: 225.9 input.voltage.fault: 225.9 input.voltage.nominal: 230 output.voltage: 225.9 ups.beeper.status: enabled ups.delay.shutdown: 60 #BAD: UPS ignores this; constant 30 second delay ups.delay.start: 60 #BAD: UPS ignores this; constant 10 second delay ups.firmware: VER 1.00 ups.load: 0 ups.productid: 0000 ups.status: OL ups.temperature: 25.0 #BAD: temperature is constant ups.type: offline / line interactive ups.vendorid: 0001 #CMD:beeper.toggle # beeper.toggle:COMMENT: # - if the beeper emits a beep at the time when command is issued the beep never ends... # - the beeper can not be switched off if UPS is on line, # - nutdrv_qx output: # + # ---- # 396.231354 instcmd(beeper.toggle, [NULL]) # 396.231400 send: Q # 396.231414 command index: 0x07 # 396.250914 read: UPS No Ack # 396.250947 instcmd: FAILED # ---- # beeper.toggle:EOC #CMD:load.off # load.off:COMMENT: # - load are switched off after ~30s, # - 'shutdown.stop' (`C` command) will not break the shutdown, # - nutdrv_qx output: http://bpa.ksu.pl/pub/nutdrv_qx_load.off.txt (4kB) # load.off:EOC #CMD:load.on # load.on:COMMENT: # - load are switched on after ~10s, # - nutdrv_qx output: http://bpa.ksu.pl/pub/nutdrv_qx_load.on.txt (2kB) # load.on:EOC #CMD:shutdown.stop #COMMENT: Stop only 'shutdown.return' #CMD:shutdown.return # shutdown.return:COMMENT: # - load is switched on immediately, 'ups.delay.start' (`R` part of the command, as in `S01R0001`) does not matter, # - 'shutdown.stop' (`C` command) can break the shutdown, # - nutdrv_qx output: http://bpa.ksu.pl/pub/nutdrv_qx_shutdown.return.txt (7kB) # shutdown.return:EOC #CMD:shutdown.stayoff # shutdown.stayoff:COMMENT: # - 'shutdown.stop' (`C` command) will not break the shutdown, # - nutdrv_qx output: http://bpa.ksu.pl/pub/nutdrv_qx_shutdown.stayoff.txt (7kB) # shutdown.stayoff:EOC