Network UPS Tools
Power Devices support
Table of Contents

Click here to see reports of other supported models from Eaton.

Note

When a user reports that a variable/command is not right then it will be highlighted by a red underline.

Bad values/ranges/etc… will get a red dashed outline or red solid left border.

The accompanying explaining comment - if provided - will be emphasized through a red dotted border on the left.

2.7.4

Report #1 with driver usbhid-ups (detailed comments available)

This device is known to work with driver usbhid-ups.

You can grab a dummy-ups compliant .dev file to simulate this device clicking here.

Some more detailed comments are available after the "Known supported…" sections.

Known supported variables

This device is known to support the following variables (values are just examples):

battery.capacity

9.00

battery.charge

100

battery.charge.low

20

battery.charge.restart

0

battery.charger.status

resting

battery.energysave

no

battery.energysave.delay

300

battery.energysave.load

5

battery.protection

yes

battery.runtime

1631

battery.type

PbAc

device.mfr

EATON

device.model

Eaton 5SC 2200i RT

device.serial

G147H18055

device.type

ups

driver.name

usbhid-ups

driver.parameter.bus

002

driver.parameter.pollfreq

30

driver.parameter.pollinterval

2

driver.parameter.port

auto

driver.parameter.product

Eaton 5SC

driver.parameter.productid

FFFF

driver.parameter.serial

G147H18055

driver.parameter.synchronous

no

driver.parameter.vendor

EATON

driver.parameter.vendorid

0463

driver.version

2.7.4

driver.version.data

MGE HID 1.40

driver.version.internal

0.41

input.current

1.80

input.frequency

49.9

input.frequency.nominal

50

input.sensitivity

normal

input.transfer.boost.low

207

input.transfer.high

276

input.transfer.low

184

input.transfer.trim.high

243

input.voltage

231.0

input.voltage.nominal

230

outlet.1.status

on

outlet.desc

Main Outlet

outlet.id

0

outlet.switchable

no

output.current

1.70

output.frequency

49.9

output.frequency.nominal

50

output.powerfactor

0.85

output.voltage

231.2

output.voltage.nominal

230

ups.beeper.status

enabled

ups.delay.shutdown

20

ups.delay.start

30

ups.efficiency

84

ups.firmware

01.06.0005

ups.load

17

ups.load.high

105

ups.mfr

EATON

ups.model

Eaton 5SC 2200i RT

ups.power

393

ups.power.nominal

2200

ups.productid

ffff

ups.realpower

337

ups.realpower.nominal

1980

ups.serial

G147H18055

ups.shutdown

enabled

ups.start.auto

yes

ups.start.battery

yes

ups.start.reboot

yes

ups.status

OL

ups.test.interval

2592000

ups.test.result

Done and passed

ups.timer.shutdown

0

ups.timer.start

0

ups.type

offline / line interactive

ups.vendorid

0463

About this device

Device dump generated by ./nut-ddl-dump.sh on Tue, 29 Nov 2022 16:53:45 +0100

Further system data or configuration examples:

Variables per upsrw eaton@localhost listing
# TODO: Convert to RW:... and RO:... markup
:; upsrw eaton@localhost
[battery.charge.low]
Remaining battery level when UPS switches to LB (percent)
Type: STRING
Maximum length: 5
Value: 20

[battery.charge.restart]
Minimum battery level for restart after power off (percent)
Type: STRING
Maximum length: 3
Value: 0

[battery.energysave]
Switch off when running on battery and no/low load
Type: STRING
Maximum length: 5
Value: no

[battery.energysave.delay]
Delay before switch off UPS if on battery and load level low (min)
Type: STRING
Maximum length: 5
Value: 300

[battery.energysave.load]
Switch off UPS if on battery and load level lower (percent)
Type: STRING
Maximum length: 5
Value: 5

[battery.protection]
Prevent deep discharge of battery
Type: STRING
Maximum length: 5
Value: yes

[input.sensitivity]
Input power sensitivity
Type: STRING
Maximum length: 10
Value: normal

[input.transfer.boost.low]
Low voltage boosting transfer point (V)
Type: STRING
Maximum length: 5
Value: 207

[input.transfer.high]
High voltage transfer point (V)
Type: STRING
Maximum length: 5
Value: 276

[input.transfer.low]
Low voltage transfer point (V)
Type: STRING
Maximum length: 5
Value: 184

[input.transfer.trim.high]
High voltage trimming transfer point (V)
Type: STRING
Maximum length: 5
Value: 243

[outlet.desc]
Outlet description
Type: STRING
Maximum length: 20
Value: Main Outlet

[output.voltage.nominal]
Nominal output voltage (V)
Type: ENUM
Option: "200"
Option: "208"
Option: "220"
Option: "230" SELECTED
Option: "240"

[ups.delay.shutdown]
Interval to wait after shutdown with delay command (seconds)
Type: STRING
Maximum length: 10
Value: 20

[ups.delay.start]
Interval to wait before (re)starting the load (seconds)
Type: STRING
Maximum length: 10
Value: 30

[ups.load.high]
Load when UPS switches to overload condition (percent)
Type: STRING
Maximum length: 5
Value: 105

[ups.shutdown]
Description unavailable
Type: ENUM
Option: "disabled"
Option: "enabled" SELECTED

[ups.start.auto]
UPS starts when mains is (re)applied
Type: STRING
Maximum length: 5
Value: yes

[ups.start.battery]
Allow to start UPS from battery
Type: STRING
Maximum length: 5
Value: yes

[ups.start.reboot]
UPS reboots when power returns during shutdown delay
Type: STRING
Maximum length: 5
Value: yes

[ups.test.interval]
Interval between self tests (seconds)
Type: STRING
Maximum length: 8
Value: 2592000
Commands per upscmd -l eaton@localhost listing
# TODO: Convert to CMD:... markup
:; upscmd -l eaton@localhost
Instant commands supported on UPS [eaton]:

beeper.disable - Disable the UPS beeper
beeper.enable - Enable the UPS beeper
beeper.mute - Temporarily mute the UPS beeper
beeper.off - Obsolete (use beeper.disable or beeper.mute)
beeper.on - Obsolete (use beeper.enable)
load.off - Turn off the load immediately
load.off.delay - Turn off the load with a delay (seconds)
load.on - Turn on the load immediately
load.on.delay - Turn on the load with a delay (seconds)
shutdown.return - Turn off the load and return when power is back
shutdown.stayoff - Turn off the load and remain off
shutdown.stop - Stop a shutdown in progress
test.battery.start.deep - Start a deep battery test
test.battery.start.quick - Start a quick battery test
test.battery.stop - Stop the battery test