Network UPS Tools - Viper 1200

Click here to see reports of other supported models from Fideltronik INIGO.

When a user reports that a variable/command is not right then it will be highlighted by a red underline.

Bad values/ranges/etc… will get a red dashed outline or red solid left border.

The accompanying explaining comment - if provided - will be emphasized through a red dotted border on the left.

2.7.3.1

Report #1 with driver nutdrv_qx (detailed comments available)

This device is known to work with driver nutdrv_qx.

You can grab a dummy-ups compliant .dev file to simulate this device clicking here.

Some more detailed comments are available after the "Known supported…" sections.

Known supported variables

This device is known to support the following variables (values are just examples):

battery.charge	`100`
battery.runtime	`600`
battery.voltage	`27.70`
battery.voltage.high	`26.00`
battery.voltage.low	`20.80`
battery.voltage.nominal	`24.0`
device.model	`1200VA`
device.type	`ups`
driver.name	`nutdrv_qx`
driver.parameter.bus	`004`
driver.parameter.chargetime	`28800`
driver.parameter.idleload	`10`
driver.parameter.offdelay	`60`
driver.parameter.ondelay	`60`
driver.parameter.pollfreq	`30`
driver.parameter.pollinterval	`2`
driver.parameter.port	`auto`
driver.parameter.product	`MEC0003`
driver.parameter.productid	`0000`
driver.parameter.runtimecal	`60,100,900,21`
driver.parameter.synchronous	`no`
driver.parameter.vendor	`MEC`
driver.parameter.vendorid	`0001`
driver.version	`2.7.3.1`
driver.version.data	`Megatec 0.06`
driver.version.internal	`0.21`
input.current.nominal	`5.2`
input.frequency	`50.0`
input.frequency.nominal	`50`
input.voltage	`225.9`
input.voltage.fault	`225.9`
input.voltage.nominal	`230`
output.voltage	`225.9`
ups.beeper.status	`enabled`
ups.delay.shutdown	`60` UPS ignores this; constant 30 second delay
ups.delay.start	`60` UPS ignores this; constant 10 second delay
ups.firmware	`VER 1.00`
ups.load	`0`
ups.productid	`0000`
ups.status	`OL`
ups.temperature	`25.0` temperature is constant
ups.type	`offline / line interactive`
ups.vendorid	`0001`

Known supported commands

This device is known to support the following NUT’s instant commands:

beeper.toggle

if the beeper emits a beep at the time when command is issued the beep never ends…
the beeper can not be switched off if UPS is on line,

nutdrv_qx output:

    396.231354  instcmd(beeper.toggle, [NULL])
    396.231400  send: Q
    396.231414  command index: 0x07
    396.250914  read: UPS No Ack
    396.250947  instcmd: FAILED

load.off
- load are switched off after ~30s,
- shutdown.stop (C command) will not break the shutdown,
- nutdrv_qx output: http://bpa.ksu.pl/pub/nutdrv_qx_load.off.txt (4kB)
load.on
- load are switched on after ~10s,
- nutdrv_qx output: http://bpa.ksu.pl/pub/nutdrv_qx_load.on.txt (2kB)
shutdown.return
- load is switched on immediately, ups.delay.start (R<n> part of the command, as in S01R0001) does not matter,
- shutdown.stop (C command) can break the shutdown,
- nutdrv_qx output: http://bpa.ksu.pl/pub/nutdrv_qx_shutdown.return.txt (7kB)
shutdown.stayoff
- shutdown.stop (C command) will not break the shutdown,
- nutdrv_qx output: http://bpa.ksu.pl/pub/nutdrv_qx_shutdown.stayoff.txt (7kB)
shutdown.stop

Stop only shutdown.return

About this device

Vendor site: http://fideltronikinigo.com/viper/viper-1200/

The blazer_usb driver did not work with this device.

test.battery.* commands were presented by driver, but do not work.

Source and additional logs: http://lists.alioth.debian.org/pipermail/nut-upsdev/2015-July/007025.html

Reported at:

https://lists.alioth.debian.org/pipermail/nut-upsdev/2015-July/007025.html

Vendor/Manufacturer information:

http://fideltronikinigo.com/viper/viper-1200/