Network UPS Tools
Power Devices support
Table of Contents

Click here to see reports of other supported models from UltraMax.

Note

When a user reports that a variable/command is not right then it will be highlighted by a red underline.

Bad values/ranges/etc… will get a red dashed outline or red solid left border.

The accompanying explaining comment - if provided - will be emphasized through a red dotted border on the left.

2.8.0.1

Report #1 with driver nutdrv_qx (detailed comments available)

This device is known to work with driver nutdrv_qx.

You can grab a dummy-ups compliant .dev file to simulate this device clicking here.

Some more detailed comments are available after the "Known supported…" sections.

Known supported variables

This device is known to support the following variables (values are just examples):

battery.voltage

27.20

device.type

ups

driver.name

nutdrv_qx

driver.parameter.bus

003

driver.parameter.device

005

driver.parameter.pollfreq

30

driver.parameter.pollinterval

2

driver.parameter.port

auto

driver.parameter.product

USB to Serial

driver.parameter.productid

5161

driver.parameter.synchronous

auto

driver.parameter.vendor

WCHCH544

driver.parameter.vendorid

0665

driver.state

quiet

driver.version

2.8.0-Windows-542-gccfb356

driver.version.data

Mustek 0.07

driver.version.internal

0.32

driver.version.usb

libusb-1.0.20 (API: 0x1000104)

input.frequency

50.0

input.voltage

242.3

input.voltage.fault

242.3

output.voltage

242.3

ups.beeper.status

enabled

ups.delay.shutdown

30

ups.delay.start

180

ups.load

13

ups.productid

5161

ups.status

OL

ups.type

offline / line interactive

ups.vendorid

0665

About this device

Reported at:

Vendor/Manufacturer information:

Further system data or configuration examples:

Data sample
This device was tried with different `ups.conf` override settings
and with the default behavior. See nearby for the other reports.

Custom built from NUT master branch snapshot.
Driver configuration
#user = root
maxretry = 3
[ultramax]
  driver = "nutdrv_qx"
  port = "auto"
  vendorid = "0665"
  productid = "5161"
  product = "USB to Serial"
  vendor = "WCHCH544"
  bus = "003"
  device = "005"
Messages of NUT startup
:; sudo upsdrvctl start
Network UPS Tools - UPS driver controller 2.8.0-Windows-542-gccfb356
Network UPS Tools - Generic Q* USB/Serial driver 0.32 (2.8.0-Windows-542-gccfb356)
USB communication driver (libusb 1.0) 0.45
Using protocol: Mustek 0.07
Can't autodetect number of battery packs [-1/27.20]
Battery runtime will not be calculated (runtimecal not set)


Jan 30 10:05:11 nas nutdrv_qx[8390]: Can't autodetect number of battery packs [-1/27.20]
Jan 30 10:05:11 nas nutdrv_qx[8390]: Battery runtime will not be calculated (runtimecal not set)
Jan 30 10:05:12 nas nutdrv_qx[8570]: Startup successful

:; sudo /usr/sbin/upsmon
Network UPS Tools upsmon 2.8.0-Windows-542-gccfb356
fopen /run/upsmon.pid: No such file or directory
Could not find PID file to see if previous upsmon instance is already running!
UPS: ultramax@localhost (primary) (power value 1)
Using power down flag file /etc/killpower

Report #2 with driver nutdrv_qx (detailed comments available)

This device is known to work with driver nutdrv_qx.

You can grab a dummy-ups compliant .dev file to simulate this device clicking here.

Some more detailed comments are available after the "Known supported…" sections.

Known supported variables

This device is known to support the following variables (values are just examples):

battery.charge

100

battery.packs

2

battery.voltage

27.20

battery.voltage.high

24

battery.voltage.low

1

device.type

ups

driver.name

nutdrv_qx

driver.parameter.bus

003

driver.parameter.pollfreq

30

driver.parameter.pollinterval

2

driver.parameter.port

auto

driver.parameter.product

USB to Serial

driver.parameter.productid

5161

driver.parameter.synchronous

auto

driver.parameter.vendor

WCHCH544

driver.parameter.vendorid

0665

driver.state

quiet

driver.version

2.8.0-Windows-542-gccfb356

driver.version.data

Mustek 0.07

driver.version.internal

0.32

driver.version.usb

libusb-1.0.20 (API: 0x1000104)

input.frequency

50.2

input.voltage

242.3

input.voltage.fault

242.3

output.voltage

242.3

ups.beeper.status

enabled

ups.delay.shutdown

30

ups.delay.start

180

ups.load

13

ups.productid

5161

ups.status

OL

ups.type

offline / line interactive

ups.vendorid

0665

About this device

Reported at:

Vendor/Manufacturer information:

Further system data or configuration examples:

Data sample
This device was tried with different `ups.conf` override settings
and with the default behavior. See nearby for the other reports.

Custom built from NUT master branch snapshot.
Driver configuration
#user = root
maxretry = 3
[ultramax]
  driver = "nutdrv_qx"
  port = "auto"
  vendorid = "0665"
  productid = "5161"
  product = "USB to Serial"
  vendor = "WCHCH544"
  bus = "003"
  default.battery.voltage.high = 24
  default.battery.voltage.low = 1
  override.battery.packs = 2

Report #3 with driver nutdrv_qx (detailed comments available)

This device is known to work with driver nutdrv_qx.

You can grab a dummy-ups compliant .dev file to simulate this device clicking here.

Some more detailed comments are available after the "Known supported…" sections.

Known supported variables

This device is known to support the following variables (values are just examples):

battery.charge

100

battery.packs

2

battery.runtime

3000

battery.voltage

27.20

battery.voltage.high

24

battery.voltage.low

1

device.type

ups

driver.name

nutdrv_qx

driver.parameter.bus

003

driver.parameter.chargetime

21600

driver.parameter.idleload

10

driver.parameter.pollfreq

30

driver.parameter.pollinterval

2

driver.parameter.port

auto

driver.parameter.product

USB to Serial

driver.parameter.productid

5161

driver.parameter.runtimecal

300,100,900,50

driver.parameter.synchronous

auto

driver.parameter.vendor

WCHCH544

driver.parameter.vendorid

0665

driver.state

quiet

driver.version

2.8.0-Windows-542-gccfb356

driver.version.data

Mustek 0.07

driver.version.internal

0.32

driver.version.usb

libusb-1.0.20 (API: 0x1000104)

input.frequency

50.2

input.voltage

242.3

input.voltage.fault

242.3

output.voltage

242.3

ups.beeper.status

enabled

ups.delay.shutdown

30

ups.delay.start

180

ups.load

13

ups.productid

5161

ups.status

OL

ups.type

offline / line interactive

ups.vendorid

0665

About this device

Reported at:

Vendor/Manufacturer information:

Further system data or configuration examples:

Data sample
This device was tried with different `ups.conf` override settings
and with the default behavior. See nearby for the other reports.

Custom built from NUT master branch snapshot.
Driver configuration
#user = nut
maxretry = 3
[ultramax]
  driver = "nutdrv_qx"
  port = "auto"
  vendorid = "0665"
  productid = "5161"
  product = "USB to Serial"
  vendor = "WCHCH544"
  bus = "003"
  default.battery.voltage.high = 24
  default.battery.voltage.low = 1
  override.battery.packs = 2
  runtimecal = 300,100,900,50
  chargetime = 21600
  idleload = 10

Report #4 with driver nutdrv_qx (detailed comments available)

This device is known to work with driver nutdrv_qx.

You can grab a dummy-ups compliant .dev file to simulate this device clicking here.

Some more detailed comments are available after the "Known supported…" sections.

Known supported variables

This device is known to support the following variables (values are just examples):

battery.charge

100

battery.packs

2

battery.runtime

3000

battery.voltage

27.40

battery.voltage.high

27.2

battery.voltage.low

21.0

battery.voltage.nominal

24.0

device.type

ups

driver.name

nutdrv_qx

driver.parameter.bus

003

driver.parameter.chargetime

21600

driver.parameter.idleload

10

driver.parameter.pollfreq

30

driver.parameter.pollinterval

2

driver.parameter.port

auto

driver.parameter.product

USB to Serial

driver.parameter.productid

5161

driver.parameter.runtimecal

300,100,900,50

driver.parameter.synchronous

auto

driver.parameter.vendor

WCHCH544

driver.parameter.vendorid

0665

driver.state

quiet

driver.version

2.8.0-Windows-542-gccfb356

driver.version.data

Mustek 0.07

driver.version.internal

0.32

driver.version.usb

libusb-1.0.20 (API: 0x1000104)

input.frequency

50.0

input.voltage

240.3

input.voltage.fault

240.3

output.voltage

240.3

ups.beeper.status

enabled

ups.delay.shutdown

30

ups.delay.start

180

ups.load

13

ups.productid

5161

ups.status

OL

ups.type

offline / line interactive

ups.vendorid

0665

About this device

Reported at:

Vendor/Manufacturer information:

Further system data or configuration examples:

Data sample
This device was tried with different `ups.conf` override settings
and with the default behavior. See nearby for the other reports.

Custom built from NUT master branch snapshot.

According to vendor, "Battery Type : 2 x 12volt 7Amps (INCLUDED)"
so this example tunes the tweaks for these values.
Driver configuration
#user = nut
maxretry = 3
[ultramax]
  driver = "nutdrv_qx"
  port = "auto"
  vendorid = "0665"
  productid = "5161"
  product = "USB to Serial"
  vendor = "WCHCH544"
  bus = "003"
  override.battery.voltage.high = 27.2
  override.battery.voltage.nominal = 24.0
  override.battery.voltage.low = 21.0
  override.battery.packs = 2
  runtimecal = 300,100,900,50
  chargetime = 21600
  idleload = 10