9E2000i

# TODO: Convert to RW:... and RO:... markup
:; upsrw Eaton9E2000i@127.0.0.1
[battery.charge.low]
Remaining battery level when UPS switches to LB (percent)
Type: STRING
Maximum length: 5
Value: 20

[battery.charge.restart]
Minimum battery level for restart after power off (percent)
Type: STRING
Maximum length: 3
Value: 0

[battery.protection]
Prevent deep discharge of battery
Type: STRING
Maximum length: 5
Value: yes

[battery.runtime.low]
Remaining battery runtime when UPS switches to LB (seconds)
Type: STRING
Maximum length: 10
Value: 180

[driver.debug]
Current debug verbosity level of the driver program
Type: NUMBER
Value: 0

[driver.flag.allow_killpower]
Safety flip-switch to allow the driver daemon to send UPS shutdown command (accessible via driver.killpower)
Type: NUMBER
Value: 0

[input.bypass.switch.off]
Take the UPS out of Bypass mode
Type: STRING
Maximum length: 12
Value: disabled

[input.bypass.switch.on]
Put the UPS in Bypass mode
Type: STRING
Maximum length: 8
Value: disabled

[input.bypass.switchable]
Input auto transfer on Bypass when overload or out of tolerance (enabled or disabled)
Type: STRING
Maximum length: 8
Value: enabled

[input.eco.switchable]
Input High Efficiency (aka ECO) mode switch
Type: STRING
Maximum length: 8
Value: ECO

[input.transfer.bypass.forced]
Rule for allow auto Bypass switch (on/off) transfer modes (enabled or disabled)
Type: STRING
Maximum length: 8
Value: enabled

[input.transfer.bypass.high]
High voltage Bypass transfer point (V)
Type: STRING
Maximum length: 5
Value: 264

[input.transfer.bypass.low]
Low voltage Bypass transfer point (V)
Type: STRING
Maximum length: 5
Value: 184

[input.transfer.bypass.overload]
Rule for auto transfer on Bypass when overload (enabled or disabled)
Type: STRING
Maximum length: 8
Value: enabled

[input.transfer.eco.high]
High voltage ECO transfer point (V)
Type: STRING
Maximum length: 5
Value: 243

[input.transfer.eco.low]
Low voltage ECO transfer point (V)
Type: STRING
Maximum length: 5
Value: 218

[input.transfer.frequency.bypass.range]
Frequency range Bypass transfer point (percent of nominal Hz)
Type: STRING
Maximum length: 5
Value: 10

[input.transfer.frequency.eco.range]
Frequency range ECO transfer point (percent of nominal Hz)
Type: STRING
Maximum length: 5
Value: 5

[input.transfer.high]
High voltage transfer point (V)
Type: STRING
Maximum length: 5
Value: 300

[input.transfer.hysteresis]
Threshold of switching protection modes, voltage transfer point (V)
Type: STRING
Maximum length: 5
Value: 10

[input.transfer.low]
Low voltage transfer point (V)
Type: STRING
Maximum length: 5
Value: 100

[outlet.desc]
Outlet description
Type: STRING
Maximum length: 20
Value: Main Outlet

[output.voltage.nominal]
Nominal output voltage (V)
Type: ENUM STRING
Maximum length: 3
Option: "200"
Option: "208"
Option: "220"
Option: "230" SELECTED
Option: "240"

[ups.delay.shutdown]
Interval to wait after shutdown with delay command (seconds)
Type: STRING
Maximum length: 10
Value: 20

[ups.delay.start]
Interval to wait before (re)starting the load (seconds)
Type: STRING
Maximum length: 10
Value: 30

[ups.load.high]
Load when UPS switches to overload condition (percent)
Type: STRING
Maximum length: 5
Value: 105

[ups.shutdown]
Enable or disable UPS shutdown ability (poweroff)
Type: ENUM STRING
Maximum length: 10
Option: "disabled"
Option: "enabled" SELECTED

[ups.start.auto]
UPS starts when mains is (re)applied
Type: STRING
Maximum length: 5
Value: yes

[ups.start.battery]
Allow to start UPS from battery
Type: STRING
Maximum length: 5
Value: yes

[ups.start.reboot]
UPS reboots when power returns during shutdown delay
Type: STRING
Maximum length: 5
Value: yes

[ups.test.interval]
Interval between self tests (seconds)
Type: STRING
Maximum length: 8
Value: 604800

# TODO: Convert to CMD:... markup
:; upscmd -l Eaton9E2000i@127.0.0.1
Instant commands supported on UPS [Eaton9E2000i]:

beeper.disable - Disable the UPS beeper
beeper.enable - Enable the UPS beeper
beeper.mute - Temporarily mute the UPS beeper
beeper.off - Obsolete (use beeper.disable or beeper.mute)
beeper.on - Obsolete (use beeper.enable)
bypass.start - Put the UPS in Bypass mode
bypass.stop - Take the UPS out of Bypass mode
driver.killpower - Tell the driver daemon to initiate UPS shutdown; should be unlocked with driver.flag.allow_killpower option or variable setting
driver.reload - Reload running driver configuration from the file system (only works for changes in some options)
driver.reload-or-error - Reload running driver configuration from the file system (only works for changes in some options); return an error if something changed and could not be applied live (so the caller can restart it with new options)
driver.reload-or-exit - Reload running driver configuration from the file system (only works for changes in some options); exit the running driver if something changed and could not be applied live (so service management framework can restart it with new options)
experimental.bypass.ecomode.start - Put UPS in Bypass mode then High Efficiency (aka ECO) mode
experimental.bypass.ecomode.stop - Take the UPS out of High Efficiency (aka ECO) mode after exiting Bypass mode
experimental.ecomode.start - Put UPS in High Efficiency (aka ECO) mode
experimental.ecomode.stop - Take the UPS out of High Efficiency (aka ECO) mode
experimental.essmode.start - Put UPS in Energy Saver System (aka ESS) mode
experimental.essmode.stop - Take the UPS out of Energy Saver System (aka ESS) mode
load.off - Turn off the load immediately
load.off.delay - Turn off the load with a delay (seconds)
load.on - Turn on the load immediately
load.on.delay - Turn on the load with a delay (seconds)
shutdown.default - Run the driver-defined UPS shutdown sequence (as opposed to user-configured 'sdcommands')
shutdown.return - Turn off the load and return when power is back
shutdown.stayoff - Turn off the load and remain off
shutdown.stop - Stop a shutdown in progress
test.battery.start.deep - Start a deep battery test
test.battery.start.quick - Start a quick battery test
test.battery.stop - Stop the battery test