Click here to see reports of other supported models from Eaton.
|
When a user reports that a variable/command is not right then it will be highlighted by a red underline. Bad values/ranges/etc… will get a red dashed outline or red solid left border. The accompanying explaining comment - if provided - will be emphasized through a red dotted border on the left. |
2.7.2
Report #1
This device is known to work with driver usbhid-ups.
You can grab a dummy-ups compliant .dev file to simulate this device clicking here.
Known supported variables
This device is known to support the following variables (values are just examples):
|
battery.charge
|
|
|
battery.charge.low
|
|
|
battery.runtime
|
|
|
battery.type
|
|
|
device.mfr
|
|
|
device.model
|
|
|
device.serial
|
Masked by the user. |
|
device.type
|
|
|
driver.name
|
|
|
driver.parameter.pollfreq
|
|
|
driver.parameter.pollinterval
|
|
|
driver.parameter.port
|
not needed; "auto" should work |
|
driver.version
|
|
|
driver.version.data
|
|
|
driver.version.internal
|
|
|
input.frequency
|
|
|
input.transfer.high
|
|
|
input.transfer.low
|
|
|
input.voltage
|
|
|
input.voltage.extended
|
|
|
outlet.1.desc
|
|
|
outlet.1.id
|
|
|
outlet.1.status
|
|
|
outlet.1.switchable
|
|
|
outlet.2.desc
|
|
|
outlet.2.id
|
|
|
outlet.2.status
|
|
|
outlet.2.switchable
|
|
|
outlet.desc
|
|
|
outlet.id
|
|
|
outlet.switchable
|
|
|
output.frequency
|
|
|
output.frequency.nominal
|
|
|
output.voltage
|
|
|
output.voltage.nominal
|
|
|
ups.beeper.status
|
|
|
ups.delay.shutdown
|
|
|
ups.delay.start
|
|
|
ups.firmware
|
|
|
ups.load
|
|
|
ups.mfr
|
|
|
ups.model
|
|
|
ups.power
|
|
|
ups.power.nominal
|
|
|
ups.productid
|
|
|
ups.realpower
|
|
|
ups.serial
|
Masked by the user. |
|
ups.status
|
|
|
ups.timer.shutdown
|
|
|
ups.timer.start
|
|
|
ups.vendorid
|
|
Known supported commands
This device is known to support the following NUT’s instant commands:
-
beeper.disable
-
beeper.enable
-
beeper.mute
-
beeper.off
-
beeper.on
-
load.off
-
load.off.delay
-
load.on
-
load.on.delay
-
shutdown.return
-
shutdown.stayoff
-
shutdown.stop
2.0.5
Report #1
This device is known to work with driver hidups, now replaced by the usbhid-ups one.
You can grab a dummy-ups compliant .dev file to simulate this device clicking here.
Known supported variables
This device is known to support the following variables (values are just examples):
|
battery.charge
|
|
|
battery.chemistry
|
|
|
battery.runtime
|
|
|
battery.voltage
|
|
|
driver.name
|
|
|
driver.parameter.lowbatt_pct
|
|
|
driver.version
|
|
|
ups.mfr
|
|
|
ups.model
|
|
|
ups.serial
|
Masked by the user. |
|
ups.status
|
|
