Network UPS Tools - Viper 1200

Click here to see reports of other supported models from Fideltronik INIGO.

When a user reports that a variable/command is not right then it will be highlighted by a red underline.

Bad values/ranges/etc… will get a red dashed outline or red solid left border.

The accompanying explaining comment - if provided - will be emphasized through a red dotted border on the left.

2.7.3.1

Report #1

This device is known to work with driver nutdrv_qx.

You can grab a dummy-ups compliant .dev file to simulate this device clicking here.

Known supported variables

This device is known to support the following variables (values are just examples):

battery.charge	`100`
battery.runtime	`600`
battery.voltage	`27.70`
battery.voltage.high	`26.00`
battery.voltage.low	`20.80`
battery.voltage.nominal	`24.0`
device.model	`1200VA`
device.type	`ups`
driver.name	`nutdrv_qx`
driver.parameter.bus	`004`
driver.parameter.chargetime	`28800`
driver.parameter.idleload	`10`
driver.parameter.offdelay	`60`
driver.parameter.ondelay	`60`
driver.parameter.pollfreq	`30`
driver.parameter.pollinterval	`2`
driver.parameter.port	`auto`
driver.parameter.product	`MEC0003`
driver.parameter.productid	`0000`
driver.parameter.runtimecal	`60,100,900,21`
driver.parameter.synchronous	`no`
driver.parameter.vendor	`MEC`
driver.parameter.vendorid	`0001`
driver.version	`2.7.3.1`
driver.version.data	`Megatec 0.06`
driver.version.internal	`0.21`
input.current.nominal	`5.2`
input.frequency	`50.0`
input.frequency.nominal	`50`
input.voltage	`225.9`
input.voltage.fault	`225.9`
input.voltage.nominal	`230`
output.voltage	`225.9`
ups.beeper.status	`enabled`
ups.delay.shutdown	`60` UPS ignores this; constant 30 second delay
ups.delay.start	`60` UPS ignores this; constant 10 second delay
ups.firmware	`VER 1.00`
ups.load	`0`
ups.productid	`0000`
ups.status	`OL`
ups.temperature	`25.0` temperature is constant
ups.type	`offline / line interactive`
ups.vendorid	`0001`

Known supported commands

This device is known to support the following NUT’s instant commands:

beeper.toggle

if the beeper emits a beep at the time when command is issued the beep never ends…
the beeper can not be switched off if UPS is on line,

nutdrv_qx output:

    396.231354  instcmd(beeper.toggle, [NULL])
    396.231400  send: Q
    396.231414  command index: 0x07
    396.250914  read: UPS No Ack
    396.250947  instcmd: FAILED

load.off
- load are switched off after ~30s,
- shutdown.stop (C command) will not break the shutdown,
- nutdrv_qx output: http://bpa.ksu.pl/pub/nutdrv_qx_load.off.txt (4kB)
load.on
- load are switched on after ~10s,
- nutdrv_qx output: http://bpa.ksu.pl/pub/nutdrv_qx_load.on.txt (2kB)
shutdown.return
- load is switched on immediately, ups.delay.start (R<n> part of the command, as in S01R0001) does not matter,
- shutdown.stop (C command) can break the shutdown,
- nutdrv_qx output: http://bpa.ksu.pl/pub/nutdrv_qx_shutdown.return.txt (7kB)
shutdown.stayoff
- shutdown.stop (C command) will not break the shutdown,
- nutdrv_qx output: http://bpa.ksu.pl/pub/nutdrv_qx_shutdown.stayoff.txt (7kB)
shutdown.stop

Stop only shutdown.return

About this device

Vendor site: http://fideltronikinigo.com/viper/viper-1200/

The blazer_usb driver did not work with this device.

test.battery.* commands were presented by driver, but do not work.

Source and additional logs: http://lists.alioth.debian.org/pipermail/nut-upsdev/2015-July/007025.html