Network UPS Tools - Newtech Pro 1KVA

Click here to see reports of other supported models from Tuncmatik.

When a user reports that a variable/command is not right then it will be highlighted by a red underline.

Bad values/ranges/etc… will get a red dashed outline or red solid left border.

The accompanying explaining comment - if provided - will be emphasized through a red dotted border on the left.

2.4.1

This device is known to work with driver megatec, now replaced by the blazer_ser one. It may also work with driver nutdrv_qx.

You can grab a dummy-ups compliant .dev file to simulate this device clicking here.

This device is known to support the following variables (values are just examples):

battery.charge	`100.0`
battery.voltage	`2.32`
battery.voltage.nominal	`36.0`
driver.name	`megatec`
driver.parameter.pollinterval	`2`
driver.parameter.port	`/dev/ttyS0`
driver.version	`2.4.1`
driver.version.internal	`1.6`
input.frequency	`50.0`
input.frequency.nominal	`50.0`
input.voltage	`214.4`
input.voltage.fault	`214.4`
input.voltage.maximum	`214.5`
input.voltage.minimum	`213.9`
input.voltage.nominal	`220.0`
output.voltage	`219.8`
ups.beeper.status	`enabled`
ups.delay.shutdown	`0`
ups.delay.start	`2`
ups.load	`20.0`
ups.mfr
ups.model	`HV 1K 00001903`
ups.serial	`unknown`
ups.status	`OL`
ups.temperature	`23.3`
ups.type	`online`

This device is known to work with driver blazer_ser. It may also work with driver nutdrv_qx.

You can grab a dummy-ups compliant .dev file to simulate this device clicking here.

This device is known to support the following variables (values are just examples):

battery.voltage	`41.76`
battery.voltage.nominal	`36.0`
beeper.status	`enabled`
driver.name	`blazer_ser`
driver.parameter.pollinterval	`2`
driver.parameter.port	`/dev/ttyS0`
driver.version	`2.4.1`
driver.version.internal	`1.51`
input.current.nominal	`4.0`
input.frequency	`50.0`
input.frequency.nominal	`50`
input.voltage	`214.5`
input.voltage.fault	`214.5`
input.voltage.nominal	`220`
output.voltage	`219.8`
ups.delay.shutdown	`30`
ups.delay.start	`180`
ups.firmware	`00001903`
ups.load	`20`
ups.mfg
ups.model	`HV 1K`
ups.status	`OL`
ups.temperature	`23.3`
ups.type	`online`

This device is known to work with driver blazer_usb. It may also work with driver nutdrv_qx.

You can grab a dummy-ups compliant .dev file to simulate this device clicking here.

This device is known to support the following variables (values are just examples):

battery.voltage	`41.76`
battery.voltage.nominal	`36.0`
beeper.status	`enabled`
driver.name	`blazer_usb`
driver.parameter.pollinterval	`2`
driver.parameter.port	`auto`
driver.version	`2.4.1`
driver.version.internal	`0.03`
input.current.nominal	`4.0`
input.frequency	`50.0`
input.frequency.nominal	`50`
input.voltage	`214.4`
input.voltage.fault	`214.4`
input.voltage.nominal	`220`
output.voltage	`219.8`
ups.delay.shutdown	`30`
ups.delay.start	`180`
ups.firmware	`00001903`
ups.load	`19`
ups.mfg
ups.model	`HV 1K`
ups.productid	`5161`
ups.status	`OL`
ups.temperature	`23.3`
ups.type	`online`
ups.vendorid	`0665`