Click here to see reports of other supported models from FSP.
|
When a user reports that a variable/command is not right then it will be highlighted by a red underline. Bad values/ranges/etc… will get a red dashed outline or red solid left border. The accompanying explaining comment - if provided - will be emphasized through a red dotted border on the left. |
2.7.4
Report #1 with driver nutdrv_qx (detailed comments available)
This device is known to work with driver nutdrv_qx.
You can grab a dummy-ups compliant .dev file to simulate this device clicking here.
Some more detailed comments are available after the "Known supported…" sections.
Known supported variables
This device is known to support the following variables (values are just examples):
|
battery.charge
|
|
|
battery.energysave
|
|
|
battery.packs
|
|
|
battery.protection
|
|
|
battery.runtime
|
|
|
battery.voltage
|
|
|
battery.voltage.nominal
|
|
|
device.model
|
|
|
device.serial
|
|
|
device.type
|
|
|
driver.name
|
|
|
driver.parameter.bus
|
|
|
driver.parameter.pollfreq
|
|
|
driver.parameter.pollinterval
|
|
|
driver.parameter.port
|
|
|
driver.parameter.productid
|
|
|
driver.parameter.synchronous
|
|
|
driver.parameter.vendorid
|
|
|
driver.version
|
|
|
driver.version.data
|
|
|
driver.version.internal
|
|
|
input.current.nominal
|
|
|
input.frequency
|
|
|
input.frequency.high
|
|
|
input.frequency.low
|
|
|
input.frequency.nominal
|
|
|
input.phases
|
|
|
input.transfer.high
|
|
|
input.transfer.high.max
|
|
|
input.transfer.high.min
|
|
|
input.transfer.low
|
|
|
input.transfer.low.max
|
|
|
input.transfer.low.min
|
|
|
input.voltage
|
|
|
input.voltage.nominal
|
|
|
outlet.0.switchable
|
|
|
output.current
|
|
|
output.current.nominal
|
|
|
output.frequency
|
|
|
output.frequency.nominal
|
|
|
output.phases
|
|
|
output.power.maximum.percent
|
|
|
output.power.minimum.percent
|
|
|
output.powerfactor
|
|
|
output.voltage
|
|
|
output.voltage.nominal
|
|
|
ups.beeper.status
|
|
|
ups.delay.shutdown
|
|
|
ups.delay.start
|
|
|
ups.firmware
|
|
|
ups.firmware.aux
|
|
|
ups.load
|
|
|
ups.power.nominal
|
|
|
ups.productid
|
|
|
ups.start.auto
|
|
|
ups.start.battery
|
|
|
ups.status
|
|
|
ups.temperature
|
|
|
ups.type
|
|
|
ups.vendorid
|
|
About this device
Device dump generated by ./nut-ddl-dump.sh on Tue, 12 Sep 2023 15:28:27 +0200
Further system data or configuration examples:
upsrw fsp@localhost listing# TODO: Convert to RW:... and RO:... markup
:; upsrw fsp@localhost
[battery.energysave]
Switch off when running on battery and no/low load
Type: ENUM
Option: "no" SELECTED
Option: "yes"
[battery.packs]
Number of battery packs
Type: RANGE
Option: "1-99" SELECTED
[battery.protection]
Prevent deep discharge of battery
Type: ENUM
Option: "no"
Option: "yes" SELECTED
[input.frequency.high]
Maximum input line frequency (Hz)
Type: RANGE
Option: "53-60" SELECTED
[input.frequency.low]
Minimum input line frequency (Hz)
Type: RANGE
Option: "40-47" SELECTED
[input.transfer.high]
High voltage transfer point (V)
Type: RANGE
Option: "237-254" SELECTED
[input.transfer.low]
Low voltage transfer point (V)
Type: RANGE
Option: "206-223" SELECTED
[outlet.0.switchable]
Description unavailable
Type: ENUM
Option: "no" SELECTED
Option: "yes"
[ups.delay.shutdown]
Interval to wait after shutdown with delay command (seconds)
Type: RANGE
Option: "12-5940" SELECTED
[ups.delay.start]
Interval to wait before (re)starting the load (seconds)
Type: RANGE
Option: "0-599940" SELECTED
[ups.start.auto]
UPS starts when mains is (re)applied
Type: ENUM
Option: "no"
Option: "yes" SELECTED
[ups.start.battery]
Allow to start UPS from battery
Type: ENUM
Option: "no"
Option: "yes" SELECTEDupscmd -l fsp@localhost listing# TODO: Convert to CMD:... markup
:; upscmd -l fsp@localhost
Instant commands supported on UPS [fsp]:
beeper.disable - Disable the UPS beeper
beeper.enable - Enable the UPS beeper
beeper.toggle - Toggle the UPS beeper
bypass.start - Put the UPS in bypass mode
bypass.stop - Take the UPS out of bypass mode
load.off - Turn off the load immediately
load.on - Turn on the load immediately
shutdown.return - Turn off the load and return when power is back
shutdown.stayoff - Turn off the load and remain off
shutdown.stop - Stop a shutdown in progress
test.battery.start - Start a battery test
test.battery.start.deep - Start a deep battery test
test.battery.start.quick - Start a quick battery test
test.battery.stop - Stop the battery test
