Network UPS Tools - U4BC02CB00NY100

Click here to see reports of other supported models from NetVision.

When a user reports that a variable/command is not right then it will be highlighted by a red underline.

Bad values/ranges/etc… will get a red dashed outline or red solid left border.

The accompanying explaining comment - if provided - will be emphasized through a red dotted border on the left.

2.7.4

Report #1 with driver snmp-ups (detailed comments available)

This device is known to work with driver snmp-ups.

You can grab a dummy-ups compliant .dev file to simulate this device clicking here.

Some more detailed comments are available after the "Known supported…" sections.

Known supported variables

This device is known to support the following variables (values are just examples):

battery.charge	`100.00`
battery.runtime	`0.00`
battery.voltage	`339.90`
device.mfr	`Net Vision 7 v7.40`
device.model	`U4BC02CB00NY100`
device.serial	`Pxxxxxxxxx`
device.type	`ups`
driver.name	`snmp-ups`
driver.parameter.mibs	`auto`
driver.parameter.pollfreq	`60`
driver.parameter.pollinterval	`2`
driver.parameter.port	`10.10.10.10`
driver.parameter.snmp_version	`v1`
driver.parameter.synchronous	`no`
driver.version	`2.7.4`
driver.version.data	`netvision MIB 0.4`
driver.version.internal	`0.97`
input.L1-N.voltage	`231.00`
input.L1.current	`1.60`
input.L2-N.voltage	`230.00`
input.L2.current	`1.60`
input.L3-N.voltage	`231.00`
input.L3.current	`1.70`
input.bypass.L1-N.voltage	`236.00`
input.bypass.L1.current	`0.00`
input.bypass.L2-N.voltage	`235.00`
input.bypass.L2.current	`0.00`
input.bypass.L3-N.voltage	`235.00`
input.bypass.L3.current	`0.00`
input.bypass.frequency	`4.90`
input.bypass.phases	`3.00`
input.frequency	`49.90`
input.phases	`3.00`
output.L1-N.voltage	`230.00`
output.L1.current	`2.00`
output.L1.power.percent	`6.00`
output.L2-N.voltage	`230.00`
output.L2.current	`2.70`
output.L2.power.percent	`8.00`
output.L3-N.voltage	`229.00`
output.L3.current	`2.60`
output.L3.power.percent	`8.00`
output.frequency	`50.00`
output.phases	`3.00`
ups.firmware.aux
ups.mfr	`Net Vision 7 v7.40`
ups.model	`U4BC02CB00NY100`
ups.serial	`Pxxxxxxxxx`
ups.status	`OL`

About this device

Reported at:

https://github.com/networkupstools/nut/issues/1732

Further system data or configuration example:

syslog start trace

upsdrvctl[27191]: No matching MIB found for sysOID '.1.3.6.1.4.1.8072.3.2.10'!
upsdrvctl[27191]: Please report it to NUT developers, with an 'upsc' output for your device.
upsdrvctl[27191]: Going back to the classic MIB detection method.
upsdrvctl[27191]: Detected U4BC02CB00NY100 on host 10.10.30.8 (mib: netvision 0.4)
upsdrvctl[27191]: Network UPS Tools - UPS driver controller 2.7.4
snmp-ups[27195]: Startup successful