Click here to see reports of other supported models from Powermatic.
|
When a user reports that a variable/command is not right then it will be highlighted by a red underline. Bad values/ranges/etc… will get a red dashed outline or red solid left border. The accompanying explaining comment - if provided - will be emphasized through a red dotted border on the left. |
2.8.1
Report #1 with driver nutdrv_qx (detailed comments available)
This device is known to work with driver nutdrv_qx.
You can grab a dummy-ups compliant .dev file to simulate this device clicking here.
Some more detailed comments are available after the "Known supported…" sections.
Known supported variables
This device is known to support the following variables (values are just examples):
|
battery.charge
|
|
|
battery.voltage
|
|
|
battery.voltage.high
|
|
|
battery.voltage.low
|
|
|
battery.voltage.nominal
|
|
|
device.type
|
|
|
driver.debug
|
|
|
driver.flag.allow_killpower
|
|
|
driver.name
|
|
|
driver.parameter.pollfreq
|
|
|
driver.parameter.pollinterval
|
|
|
driver.parameter.port
|
|
|
driver.parameter.synchronous
|
|
|
driver.state
|
|
|
driver.version
|
|
|
driver.version.data
|
|
|
driver.version.internal
|
|
|
driver.version.usb
|
|
|
input.voltage
|
|
|
input.voltage.fault
|
|
|
output.current.nominal
|
|
|
output.frequency
|
|
|
output.frequency.nominal
|
|
|
output.voltage
|
|
|
output.voltage.nominal
|
|
|
ups.beeper.status
|
|
|
ups.delay.shutdown
|
|
|
ups.delay.start
|
|
|
ups.firmware.aux
|
|
|
ups.load
|
|
|
ups.productid
|
|
|
ups.status
|
|
|
ups.type
|
|
|
ups.vendorid
|
|
About this device
The vendor website is in Thai, but Google Translate does a pretty good job of translating the site to English.
I have tested the shutdown sequence.
Reported at:
Vendor/Manufacturer information:
Further system data or configuration examples:
upsrw 2e-ps1000l@localhost listing# TODO: Convert to RW:... and RO:... markup
:; upsrw 2e-ps1000l@localhost
[driver.debug]
Current debug verbosity level of the driver program
Type: NUMBER
Value: 0
[driver.flag.allow_killpower]
Safety flip-switch to allow the driver daemon to send UPS shutdown command (accessible via driver.killpower)
Type: NUMBER
Value: 0
[ups.delay.shutdown]
Interval to wait after shutdown with delay command (seconds)
Type: RANGE NUMBER
Option: "12-540" SELECTED
[ups.delay.start]
Interval to wait before (re)starting the load (seconds)
Type: RANGE NUMBER
Option: "60-599940" SELECTEDupscmd -l 2e-ps1000l@localhost listing# TODO: Convert to CMD:... markup
:; upscmd -l 2e-ps1000l@localhost
Instant commands supported on UPS [2e-ps1000l]:
beeper.toggle - Toggle the UPS beeper
driver.killpower - Tell the driver daemon to initiate UPS shutdown; should be unlocked with driver.flag.allow_killpower option or variable setting
driver.reload - Reload running driver configuration from the file system (only works for changes in some options)
driver.reload-or-error - Reload running driver configuration from the file system (only works for changes in some options); return an error if something changed and could not be applied live (so the caller can restart it with new options)
driver.reload-or-exit - Reload running driver configuration from the file system (only works for changes in some options); exit the running driver if something changed and could not be applied live (so service management framework can restart it with new options)
load.off - Turn off the load immediately
load.on - Turn on the load immediately
shutdown.return - Turn off the load and return when power is back
shutdown.stayoff - Turn off the load and remain off
shutdown.stop - Stop a shutdown in progress
test.battery.start - Start a battery test
test.battery.start.deep - Start a deep battery test
test.battery.start.quick - Start a quick battery test
test.battery.stop - Stop the battery test
