Click here to see reports of other supported models from Delta.
|
When a user reports that a variable/command is not right then it will be highlighted by a red underline. Bad values/ranges/etc… will get a red dashed outline or red solid left border. The accompanying explaining comment - if provided - will be emphasized through a red dotted border on the left. |
2.7.4-1-gb34f2434
Report #1 with driver usbhid-ups (detailed comments available)
This device is known to work with driver usbhid-ups.
You can grab a dummy-ups compliant .dev file to simulate this device clicking here.
Some more detailed comments are available after the "Known supported…" sections.
Known supported variables
This device is known to support the following variables (values are just examples):
|
battery.capacity
|
|
|
battery.charge
|
|
|
battery.charge.low
|
|
|
battery.charge.warning
|
|
|
battery.runtime
|
|
|
battery.temperature
|
|
|
battery.voltage
|
|
|
battery.voltage.nominal
|
|
|
device.mfr
|
|
|
device.model
|
|
|
device.serial
|
|
|
device.type
|
|
|
driver.name
|
|
|
driver.parameter.pollfreq
|
|
|
driver.parameter.pollinterval
|
|
|
driver.parameter.port
|
|
|
driver.parameter.synchronous
|
|
|
driver.version
|
|
|
driver.version.data
|
|
|
driver.version.internal
|
|
|
input.frequency
|
|
|
input.sensitivity
|
|
|
input.source
|
|
|
input.transfer.high
|
|
|
input.transfer.high.max
|
|
|
input.transfer.high.min
|
|
|
input.transfer.low
|
|
|
input.transfer.low.max
|
|
|
input.transfer.low.min
|
|
|
input.voltage
|
|
|
output.current
|
|
|
output.frequency
|
|
|
output.frequency.nominal
|
|
|
output.voltage
|
|
|
output.voltage.nominal
|
|
|
ups.beeper.status
|
|
|
ups.delay.start
|
|
|
ups.load
|
|
|
ups.mfr
|
|
|
ups.model
|
|
|
ups.power.nominal
|
|
|
ups.productid
|
|
|
ups.realpower
|
|
|
ups.serial
|
|
|
ups.start.auto
|
|
|
ups.status
|
|
|
ups.timer.reboot
|
|
|
ups.timer.shutdown
|
|
|
ups.timer.start
|
|
|
ups.type
|
|
|
ups.vendorid
|
|
About this device
Device dump generated by ./tools/nut-ddl-dump.sh on Wed, 21 Apr 2021 01:02:14 +0900
Further system data or configuration examples:
upsrw delta@localhost listing# TODO: Convert to RW:... and RO:... markup
:; upsrw delta@localhost
[battery.charge.low]
Remaining battery level when UPS switches to LB (percent)
Type: STRING
Maximum length: 5
Value: 20
[input.sensitivity]
Input power sensitivity
Type: NUMBER
[input.transfer.high]
High voltage transfer point (V)
Type: NUMBER
[input.transfer.low]
Low voltage transfer point (V)
Type: NUMBER
[ups.delay.start]
Interval to wait before (re)starting the load (seconds)
Type: NUMBER
[ups.start.auto]
UPS starts when mains is (re)applied
Type: NUMBERupscmd -l delta@localhost listing# TODO: Convert to CMD:... markup
:; upscmd -l delta@localhost
Instant commands supported on UPS [delta]:
beeper.disable - Disable the UPS beeper
beeper.enable - Enable the UPS beeper
beeper.mute - Temporarily mute the UPS beeper
beeper.off - Obsolete (use beeper.disable or beeper.mute)
beeper.on - Obsolete (use beeper.enable)
load.off - Turn off the load immediately
load.off.delay - Turn off the load with a delay (seconds)
load.on - Turn on the load immediately
load.on.delay - Turn on the load with a delay (seconds)
shutdown.reboot - Shut down the load briefly while rebooting the UPS
shutdown.return - Turn off the load and return when power is back
shutdown.stayoff - Turn off the load and remain off
shutdown.stop - Stop a shutdown in progress
test.battery.start.deep - Start a deep battery test
test.battery.start.quick - Start a quick battery test
test.battery.stop - Stop the battery test
